About our "Classic"

imigi, a division of Adona Corporation

Which tastes better, an apple or an orange? Here's your chance to try a peach! This classic rack framework is now available with maple platforms, multi-layer granite platforms, or any combination of the two. You can also get your maple platforms in a matching, beveled-edge, jet black version! Or, you can get you granite platforms with coordinating wood trim.

UPS shippable.
List Price: $917.00 (as pictured, 3-level w/ silver columns)
List Price: $1222.00 (4-level w/ silver columns)
List Price: $1528.00 (5-level w/ silver columns)

For black columns add $20.00 per level.
Solid brass floor cones are included.

Design your own rack rack with our Do it Yourself rack building parts.

Imigi is proud to offer these affordable, "audio-grade", solid maple component platforms. Unlike our "audiophile-grade" platforms (which use flat-grain, thick wood construction), these are constructed using 1 inch thick strips of kiln-dried lumber in a single layer, end-grain construction. This method of construction is much less prone to warpage than single layer, flat-grain construction but with a slight compromize in sonic performance. Yet, these platforms still offer superior performance over traditional "butcher-block" materials found in hardware and kitchen supply stores.

All platforms are surface planed, beveled on all edges, sanded and finished with four coats of clear lacquer.

The standard platform size is 18 x 18 x 1.5" inches. This size works well with most components so long as the feet will land within an 18 x 18 inch square. An 19" x 24" platform is available for an extra $100.00 per level. Mix and match sizes as you please.

The shelf support-frame utilizes heavy-gauge steel tubing fully welded at the center point to increase torsional stiffness. We call this the "X-Frame". The attachment plates are fabricated from 1/4 inch steel plate. Steel, rings like a bell unless it is properly damped, so the weight of the platform rests at points that interfere with the linear resonance of the tube, well out of the band of the more troublesome lower harmonics. When filled with sand (or lead shot), the frame becomes about as sonic as "a stick in the mud" yet it continues to couple energy toward the floor. Leveling is provided by a 1/4-20 conical set screw and jam nut at each leg of the support frame.

The X-frames are available in your choice a black, silver or gold at no extra charge.

.

The support columns, extruded from aluminum, feature full length T-slots or channels. These slots provide attachment points along the entire length of the strut through the use of a special nut called a T-nut. This design has been used for many years now in the construction of industrial furniture and machinery frames. It is strong and versatile.

The price of the rack includes silver columns. The columns are also available in black for a small additional cost.

.

Floor contact may be made in several ways. The cost of the rack includes a set of large solid brass floor cones. The base of each support column features industry standard 1/4-20 threads. A range of aftermarket feet may be installed.

The brass cones may be substituted for leveling pads or "glides" at no extra charge. Optionally, we can provide 1/2" or 12mm threads at the base of the columns for an additional charge. We also offer heavy-duty (1000 pound) casters. They have 1/2" threads and cost $100.00 per set of four.

.

Specifications:

Shipping weight 110 lbs. (3-shelf version)

Load capacity: 300 pounds per level

Overall Dimensions: Width 24.5", Depth 24.5", height 36" (other heights available)

Platform size: Standard= 18"x18", Optional= 18x24, 19x24, 21x26(top level only)

Maximum component size: Lower shelves: 20" wide, 26" deep

Maximum component size: w/ optional turntable top shelf: 26" wide, 21" deep

Shelf spacing: Infinite adjustment